+ Reply to Thread
Page 3 of 3 FirstFirst 1 2 3
Results 21 to 23 of 23

Thread: 1888 Trapdoor

Click here to increase the font size Click here to reduce the font size
  1. #21
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Today @ 03:32 PM
    Location
    Virginia
    Posts
    1,588
    Local Date
    10-03-2024
    Local Time
    04:22 PM
    Thread Starter
    I don't want to go to the range with a file in hand to set my new front sight height, and certainly don't want to waste ammo getting it just so. Instead, here is a little math.

    1) Set your rear peep to where you want it. I set the arrow at the bottom of the triangle of the buffington sight at the 300 yd mark. This puts the peep somewhere below the 200 mark, with just a tad of room left to adjust down if needed before the peep gets obstructed.

    2)We need the height P of the peep above the bore axis. OD radius of the barrel at the rear of the sight base is ~ 1.000/2, the thickness of the sight base is 0.115, and I have the peep at 0.275 above that. Add all these up to get P.

    3) use your favorite ballistics calculator, with sight height set to 0, weight velocity and BC of whatever bullet you shoot, and the zero of whatever distance you want. I want 100yds and the later-original 500gr round nose at a mild ~1200 fps. If you want the 200 or 300 marks on the rear sight to be exact for your load, set it there, calculate P, and set your calculator with zero at that distance. The drop (in MOA) at 1yd gives you a very close approximation to the launch angle, which is the same as the angle you need between the peep and front sight tip. Close-nuff-fer-govt-werk. Call this angle alpha. If you want alpha exactly, you will need some calculus to get the 100 yard drop with zero-distance set to zero. Fortunately, my calculator lets me use 0.0001 yards as my zero distance.

    4) Let h(P) be the height of the front sight above the bore axis needed when the rear peep is at P. Drawing a picture, it's easy to see that
    h(P) = P-R*tan(alpha)
    where R is the sight radius (21+5/8 on my rifle). Don't forget to convert alpha from MOA to radians or degrees for whatever calculator you are using!

    5) Subtract off the OD radius at the muzzle to get the blade height needed. In my case, I need 0.432 for the 500gr round nose, and 0.431 for the 405 gr hollow base. Don't fuss too much, as likely the cast bullet BC's online you found were all over the place, and you made your best guess, and notice that the extreme spread of blade calculated blade heights for these BC's was maybe +/- 3thous. You're just trying to get on paper, then we can use that data point to dial in anything left to do.

    Now, the square blade I got from SSfirearms is 0.412. If I run the calculation again with an extra 3MOA for a 6'0clock hold, I get pretty close enough to what I have without needing to shorten really. We are close enough to be on paper. All I need to do then is slope the blade forward to the profile I like. The original blade that bubba had soldered in place was exactly 0.445. He must have known what he was doing, or got lucky experimentally

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #22
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Today @ 03:32 PM
    Location
    Virginia
    Posts
    1,588
    Local Date
    10-03-2024
    Local Time
    04:22 PM
    Thread Starter

    Pictures!

    Very happy how this turned out. We'll shoot it, and decide if we want to re-cut the crown to fix the heavy cleaning rod wear. I'm guessing nothing spectacular or outright abysmal first time out. That wear is pretty bad, and uneven.







  4. Thank You to ssgross For This Useful Post:


  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #23
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 03:52 PM
    Location
    Victoria BC
    Posts
    30,334
    Real Name
    Jim
    Local Date
    10-03-2024
    Local Time
    01:22 PM
    Nice...
    Regards, Jim

+ Reply to Thread
Page 3 of 3 FirstFirst 1 2 3

Similar Threads

  1. Springfield 1888 .45-70
    By Doug Bowser in forum WTS/WTB/WTT (Want to Sell, Buy or Trade) Forum
    Replies: 0
    Last Post: 04-16-2021, 09:59 AM
  2. Sincerely Would Like SRS lookup on my 1888 Trapdoor
    By GySgt USMC in forum Other U.S. Service Rifles
    Replies: 5
    Last Post: 04-15-2017, 12:28 AM
  3. Would Appreciate an SRS lookup for my 1888 Trapdoor
    By Plysskin in forum Other U.S. Service Rifles
    Replies: 3
    Last Post: 11-24-2016, 08:25 AM
  4. 1888/91 Mannlicher ID Help
    By Tul8202 in forum Mauser Rifles
    Replies: 3
    Last Post: 03-20-2014, 09:52 AM
  5. 1888 carbine
    By 303 Collector in forum Mauser Rifles
    Replies: 8
    Last Post: 11-10-2013, 12:05 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts