+ Reply to Thread
Results 1 to 9 of 9

Thread: L4 Firing Pin Mark

Click here to increase the font size Click here to reduce the font size

Hybrid View

peregrinvs L4 Firing Pin Mark 05-19-2010, 04:58 PM
Brit plumber Sounds very much like it, I... 05-19-2010, 10:37 PM
tankhunter You are correct. The L7 GPMG... 05-20-2010, 02:50 AM
peregrinvs Thanks for that. On closer... 05-20-2010, 04:22 PM
tankhunter Hi Mark, Without seeing the... 05-21-2010, 03:14 AM
Brian Dick Sure sounds like they were... 05-22-2010, 04:55 PM
Peter Laidler The rectangular mark that... 05-30-2010, 07:28 AM
Bruce_in_Oz That interesting Nigerian... 05-31-2010, 01:05 AM
peregrinvs Thanks. For my own sad... 05-30-2010, 02:30 PM
  1. #1
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 12:59 PM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,654
    Real Name
    Peter Laidler
    Local Date
    05-16-2025
    Local Time
    11:18 AM
    The rectangular mark that sits 1/3rd the way across the base is from the flat ejector that whacks them out of the gun. I remember in the early 80's, we had a load of 'foreign' blank that was in boxes marked with a green/white/green band. One of the ammo techs told me that it was Nigerian from some as-per-usual one sided trade deal where we gave them, say, 1,000 as new FTR's Bedford RL trucks, worth millions and they gave us £50,000 worth of pure horse manure blank ammo from some bankrupt crooked ammo plant, owned by the big Bwana's son. But I digress as is usual...........

    Anyway, this stuff was full of dynamite mixed with ammatol mixed with PE4 and a bit of semtex for good measure. Even on the lowest gas setting, it was shaking the poor Bren guns apart and the cases flew out, hit the ground with such force, they bounced up and flew into orbit around the sun. Anyway, they took it all back and replaced it with some RG stuff after a few months, when the need for rear echelon TA troops in training was well past... as is usual!
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. Thank You to Peter Laidler For This Useful Post:


  3. #2
    Legacy Member Bruce_in_Oz's Avatar
    Join Date
    Jun 2008
    Last On
    Yesterday @ 06:12 PM
    Location
    Brisbane
    Posts
    2,284
    Local Date
    05-16-2025
    Local Time
    08:18 PM

    That interesting Nigerian blank ammo

    Quote Originally Posted by Peter Laidlericon View Post
    The rectangular mark that sits 1/3rd the way across the base is from the flat ejector that whacks them out of the gun. I remember in the early 80's, we had a load of 'foreign' blank that was in boxes marked with a green/white/green band. One of the ammo techs told me that it was Nigerian from some as-per-usual one sided trade deal where we gave them, say, 1,000 as new FTR's Bedford RL trucks, worth millions and they gave us £50,000 worth of pure horse manure blank ammo from some bankrupt crooked ammo plant, owned by the big Bwana's son. But I digress as is usual...........

    Anyway, this stuff was full of dynamite mixed with ammatol mixed with PE4 and a bit of semtex for good measure. Even on the lowest gas setting, it was shaking the poor Bren guns apart and the cases flew out, hit the ground with such force, they bounced up and flew into orbit around the sun. Anyway, they took it all back and replaced it with some RG stuff after a few months, when the need for rear echelon TA troops in training was well past... as is usual!
    I had the dubious pleasure of trying that stuff in blank firing rifles for film and TV in the late 80's. The best thing about it was the box it came in. The re-chambered M-1 Garands did not like it one bit and the L1A1 s with their regulators on max exhaust setting still flung the empties a fair distance. Changing the restrictor plugs in the bores to one with a bigger hole was not entirely successful as the reduced bore pressure reduced the combustion efficiency of the ammo and thus filled the rifles with partially burnt powder. Worked well in bolt-actions though, until the unburnt powder buildup got out of control!

    Custom blanks were always better, anyway, as you can tune ammo to guns and control the amount of flash and, to a certain extent, noise, a whole lot better. A small addition of Pyrodex adds a nice bit of cinematic flash and smoke to 9mm blanks, for instance.

    It was all a bit bizarre working in the fantasy factory. Classic example was the art director on one production demanding more flash from an M-16 muzzle. Specifically, he wanted to know why he could not have that "star" pattern flash like in the movies. (Art imitating art, there is a lot of it about!). I briefly considered explaining that the flash hider was working as advertised and HIDING most of the flash, but instead disappeared to the workshop. There I built new bore restrictors that extended half the length of the flash hider. Around the circumference were six tiny holes that lied up with the slots in the birdcage. One in the forward end to complete the set and voila; spectacular flash patterns from a flash "hider".

  4. Avoid Ads - Become a Contributing Member - Click HERE
+ Reply to Thread

Similar Threads

  1. Firing Pin Spring ?
    By Hylander in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 8
    Last Post: 05-01-2010, 12:03 AM
  2. 03A3 Firing Pin Rod
    By lonewolf in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 3
    Last Post: 08-09-2009, 06:59 PM
  3. Proof mark or import mark?
    By buchkshot in forum M1 Garand/M14/M1A Rifles
    Replies: 10
    Last Post: 04-15-2009, 03:34 PM
  4. Dry firing block?
    By Bob Womack in forum M1 Garand/M14/M1A Rifles
    Replies: 5
    Last Post: 04-05-2009, 02:55 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Loading...