5.7 Johnson and M1 Carbine

[browningautorifle]

a few hundred formed from 5.56

That's an interesting side note. I never thought about making 7.62x25 from 5.56 brass... We still have far more steel around although most ammo is harder to find now.

Information

Warning: This is a relatively older thread This discussion is older than 360 days. Some information contained in it may no longer be current.

[floydthecat]

That's an interesting side note. I never thought about making 7.62x25 from 5.56 brass... We still have far more steel around although most ammo is harder to find now.

Nothing to it. The TOK sizing die easily creates the shoulder. I use .223, 5.56 and 300AAC brass.

[browningautorifle]

I use .223, 5.56 and 300AAC brass.

With some inside case neck reaming I would suspect? I made about 600 rds of 7.92 Kurz decades ago for a man with an MP44 and used Federal once fired .308. Had all the toys to work with including the inside case neck ream...

[floydthecat]

With some inside case neck reaming I would suspect? I made about 600 rds of 7.92 Kurz decades ago for a man with an MP44 and used Federal once fired .308. Had all the toys to work with including the inside case neck ream...

After I size, I hit the mouth with a 19/64 drill bit, but anything close to .300 works. It has to be cleaned up a tad before it can be flared or the flaring die might hang-up on the mouth edge. I don’t flare much at all, just enough to start the bullet.

[RCS]

Years ago I found and bought 100 rds of yellow box Remington 30 Mauser pistol ammo, later Midway offered 7,62 or 7,63 empty brass too (along with 8mm Nambu). I found the 30 Mauser (7,62x25) in an old sporting goods store. Used 93gr lead bullets, 85 gr jackets and 100 gr half jackets in my Mauser 96 with light loads of Unique.

There was a popular wildcat 22/7,63x25 cartridge with barrels made for the Czech Model 52 pistol some twenty years ago

Mauser pistol target at 25 meters, should have used the stock

[eb in oregon]

Years ago I found and bought 100 rds of yellow box Remington 30 Mauser pistol ammo, later Midway offered 7,62 or 7,63 empty brass too (along with 8mm Nambu). I found the 30 Mauser (7,62x25) in an old sporting goods store. Used 93gr lead bullets, 85 gr jackets and 100 gr half jackets in my Mauser 96 with light loads of Unique.

There was a popular wildcat 22/7,63x25 cartridge with barrels made for the Czech Model 52 pistol some twenty years ago

Mauser pistol target at 25 meters, should have used the stockAttachment 127465

When I started working with the 7.62x25 I ran the lighter loads through a C96 Mauser. Actually I had two at the time. The lighter loads worked swell, but once I started reaching the higher limits of the Mauser cartridge I used the CZ 52 expressly. I some times think I should of kept those two C96 pistols, but there is only enough room and so much money.

[eb in oregon]

Nothing to it. The TOK sizing die easily creates the shoulder. I use .223, 5.56 and 300AAC brass.

As mentioned when I first started working with 7.62x25 there was no new commercial boxer primed brass available that didn't include buying really expensive commercial ammunition so I formed two hundred from 5.56 brass. First shortened, then formed, inside neck reamed, resized again, then trimmed to length. A lot of work. Then about eight months later Starline started making brass and I bought a few hundred more. Much easier. While there is "nothing to it" it is labor intensive and I see no reason to make something I can buy readily. I only make stuff I can't find anywhere else (such as 5.7MMJ) as then you can spend more time shooting it than making it. I try to save the "making" part for absolute need.

Edit: It's labor intensive enough that I'd put up a large tarp to catch the brass as a CZ 52 launches cases like an Olympic javelin thrower. Losing a few cases was almost physically painful after all that work.