-
Index of Peter Laidler's on-line series of articles.......
Capt. Peter Laidler is the senior Armourer in the UK Military, now retired, but based as a Technical Officer at the UK Military Small Arms School. On behalf of MILSURPS.COM members, we'd like to publicly thank him for his support of this forum, as well the broader Lee Enfield collector community in general.
In addition to being a trained and highly experienced military Armourer, he has authored two excellent books about the No.4(T) sniper rifles and their No.32 scopes. They are titled "An Armourer's Perspective: .303 No.4(T) Sniper Rifle", which he co-authored with Ian Skennerton and his own dedicated work, "Telescope Sighting No.32".
If you're really interested in some in-depth learning about the No.4(T) sniper rifles and the No.32 series of scopes, their history, evolution, repair and adjustments for shooting, we'd highly recommend those two books, which are pictured below.
(Click PIC to Enlarge)
Note: The opinions expressed herein or statements made in these articles are solely those of the author, and do not necessarily reflect the views of the Military Surplus Collectors Forums, or the ownership and moderation group of this site. MILSURPS.COM accepts no legal liability or responsibility for any claims made or opinions expressed herein. Also, please note that neither the author nor MILSURPS.COM recommends that any member of these forums, or a reader of this article, try this type of experimentation without the proper knowledge, equipment and training.
Information
|
Warning: This is a relatively older thread This discussion is older than 360 days. Some information contained in it may no longer be current. |
|
Last edited by Badger; 10-24-2013 at 08:43 AM.
-
The Following 88 Members Say Thank You to Badger For This Useful Post:
1812we1,
25-5,
728shooter,
aircav73,
Al Diehl,
andya1thomas,
aqbill,
art of empty hand,
Ax.303,
Bearclaw,
boltguns,
boomer656,
bow,
Brian Dick,
brnom2,
Buccaneer,
CINDERS,
colonel blimp,
csmarcher,
Dan.lord,
DanL96a1,
Dave_n,
Drill Sergeant,
ed skeels,
enbloc8,
fal308,
fat fred,
firefly4791,
Flying10uk,
Frank46,
gew8805,
Gnr527,
gravityfan,
Gripster,
gunner,
GUTS,
Harlan (Deceased),
henry r,
ickmann,
JimF4M1s (Deceased),
jimmieZ,
jmoore,
JOHN42768,
Kiwi,
Kiwisteve,
kryten,
limpetmine,
Lou Cypher,
MAC702,
madcratebuilder,
Mayhem,
Mikey,
Mumbles,
NavyEngineer,
No4Mk1(T),
Obendorf98,
pairtree,
Patt1903,
Pattern14,
Phrogpilot,
postino,
PrinzEugen,
rayg,
rick2gun,
Riter,
Roger Payne,
Rumpelhardt,
Salt Flat,
sean1960,
silverfox,
Simon P,
smellie,
SpikeDD,
sprog,
Stigmata,
Stu,
tbonesmith,
TCC002,
Toos,
trg22salem,
UNPROFOR1994,
Valleysniper,
WallyG.,
wazza2222,
xa-coupe,
XLesky
-
11-14-2009 12:57 PM
# ADS
Friends and Sponsors
-
Legacy Member
Just for your information: the booklet by Peter Laidler, ‘Telescope Sighting No.32’ , is back in stock at DS military books:
Telescope Sighting No.32 - Including the No.42, No.53 L1A1
-
The Following 3 Members Say Thank You to ToineS For This Useful Post:
-
-
Contributing Member
Attaching Scopes with epoxy resin
Hi Peter,
I saw a post of yours the other day, re:- attaching scopes with epoxy resins/Bonding agents, I think it was regarding a WW1 smle re-pop. Just to let you know, the fellow who argued that they assemble planes like that these days, which is true! However, a lot was left out.
I did a fair amount of research and experimentation into building motorcycle front suspension systems via this method, in particular, the interface points between the Aluminium weight force transition parts, as all the fasteners have to go into metal, as carbon fibre/resin cannot do that. So everywhere and anywhere you need a screw or bolt you have to add a sufficient metal part to take the resultant stresses.
Now in this case of sticking a scope onto a receiver, theoretically it could work, but to a few things most don't know, the two surfaces of the metal must be knurled up sufficiently for the loads, an intermediary coating of a suitable inert resin must then be applied as Those types of resins which should take those loads are electrolytic, then at a suitable point in the drying o resin cycle a) you apply the second resin b). With this, all done correctly a bond of incredible strength is achieved. This is fine where I'm inserting a dumb piece of aluminum and machining to suit after, or in the aircraft industry where they have experimented sufficiently to prefab wing sections appropriately. To your point, it isn't suitable at present, because how would you do all this and maintain the tolerances you require to mount a scope, for the now, that would be the issue I think.
I can see a point soon where it will be done especially as we move towards more plastic and aluminum parts in Gun manufacturing. Not on steel to steel through, the old tried and true method is still best, with the solder acting as the buffer between the two surfaces. He has no concept of the cost involved in achieving that idea either including a life or two. Interesting thought though, wrong materials, but not impossible.
Regards Ian
-