+ Reply to Thread
Results 1 to 4 of 4

Thread: How to install selector lever/cutoff

Click here to increase the font size Click here to reduce the font size
  1. #1
    Senior Member daveboy's Avatar
    Join Date
    May 2009
    Last On
    07-26-2020 @ 08:25 PM
    Location
    Alabama
    Posts
    177
    Local Date
    08-04-2020
    Local Time
    03:11 PM

    How to install selector lever/cutoff

    It's been a long time since I took a Kragicon down completely. Today, I did just that. Now, I'm having a hard time getting the magazine cut-off back in the rifle. I know it's just a matter of pressing down that plunger and pushing it in. But, there has to be a trick to it because I simply can't hold the plunger in far enough and put pressure on the lever at the same time. Any help?
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
     

  3. #2
    Really Senior Member butlersrangers's Avatar
    Join Date
    Nov 2009
    Last On
    Today @ 12:03 AM
    Location
    S.E. Michigan, U.S.A.
    Posts
    485
    Local Date
    08-04-2020
    Local Time
    04:11 PM
    You start the cut-off's shaft into its hole in the receiver until the detent-pin stops progress. Then use a small screwdriver tip to depress the detent-pin, while advancing the cut-off forward into place. (Kind of the reverse of attached sketch).

    It helps if the detent-pin is lubricated and not bound up with ancient dried grease.


  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Senior Member daveboy's Avatar
    Join Date
    May 2009
    Last On
    07-26-2020 @ 08:25 PM
    Location
    Alabama
    Posts
    177
    Local Date
    08-04-2020
    Local Time
    03:11 PM
    Thread Starter
    Quote Originally Posted by butlersrangers View Post
    You start the cut-off's shaft into its hole in the receiver until the detent-pin stops progress. Then use a small screwdriver tip to depress the detent-pin, while advancing the cut-off forward into place. (Kind of the reverse of attached sketch).

    I tried doing that last night. Just got frustrated. I'm gonna give it a go again today. Thanks

  6. #4
    Really Senior Member butlersrangers's Avatar
    Join Date
    Nov 2009
    Last On
    Today @ 12:03 AM
    Location
    S.E. Michigan, U.S.A.
    Posts
    485
    Local Date
    08-04-2020
    Local Time
    04:11 PM
    Soak your cut-off in some Hoppe's #9, overnight. Press and work the detent-pin, against a piece of hardwood, before trying to install. It is amazing the 'red gunk' that gets pumped out of the assembly, sometimes.


+ Reply to Thread

Similar Threads

  1. No. 4 Mk1 Safety selector
    By NORTEXED in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 2
    Last Post: 08-22-2017, 02:10 PM
  2. STEN Mk II - welded fire selector
    By Charlie303 in forum Other LMG/HMG and SMG Forum
    Replies: 9
    Last Post: 08-14-2014, 03:47 PM
  3. Which cutoff for my 1903
    By Bobrm2 in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 4
    Last Post: 07-05-2010, 12:36 PM
  4. M1A Installing a homemade dummy selector
    By general Ike in forum M1 Garand/M14/M1A Rifles
    Replies: 0
    Last Post: 12-28-2009, 07:49 PM
  5. DS Arms Semi-Auto Extended Selector/Safety Switch
    By The Wizard in forum FNFAL Rifles
    Replies: 1
    Last Post: 04-01-2009, 05:37 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts