+ Reply to Thread
Results 1 to 7 of 7

Thread: Who is/was N66 among #4 supplier codes????

Click here to increase the font size Click here to reduce the font size

Hybrid View

  1. #1
    FREE MEMBER
    NO Posting or PM's Allowed
    me2's Avatar
    Join Date
    Feb 2008
    Last On
    02-23-2012 @ 01:03 PM
    Posts
    175
    Local Date
    04-25-2025
    Local Time
    04:46 PM

    Who is/was N66 among #4 supplier codes????

    Found N66 stamped on the left side of receiver all the way to the front next to the receiver ring. This is on my Maltby which is dated 1942. I have scoured my big Skennertonicon book and can not find that code. Anybody know who it may be?
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. #2
    Legacy Member Mk VII's Avatar
    Join Date
    Dec 2008
    Last On
    04-23-2025 @ 05:08 PM
    Location
    England
    Age
    63
    Posts
    1,432
    Real Name
    James West
    Local Date
    04-25-2025
    Local Time
    09:46 PM
    Scottish Motor Traction, Edinburgh.

  3. Avoid Ads - Become a Contributing Member - Click HERE
  4. #3
    FREE MEMBER
    NO Posting or PM's Allowed
    me2's Avatar
    Join Date
    Feb 2008
    Last On
    02-23-2012 @ 01:03 PM
    Posts
    175
    Local Date
    04-25-2025
    Local Time
    04:46 PM
    Thread Starter
    Thank you. I figured the N meant Northern district but did Scottish Motor Traction actually make Receivers for the #4 rifles or perform certain machining operations on them.

  5. #4
    Legacy Member Mk VII's Avatar
    Join Date
    Dec 2008
    Last On
    04-23-2025 @ 05:08 PM
    Location
    England
    Age
    63
    Posts
    1,432
    Real Name
    James West
    Local Date
    04-25-2025
    Local Time
    09:46 PM
    They certainly didn't make them; as a bus operator they would have had a machine shop but not much more.

  6. #5
    Legacy Member krinko's Avatar
    Join Date
    Aug 2008
    Last On
    01-28-2024 @ 02:39 PM
    Location
    Omaha-ha-ha, Nebraska
    Posts
    337
    Local Date
    04-25-2025
    Local Time
    02:46 PM
    Is the "N 66" mark round?
    If so, it's going to be one of the unique Maltby "inspector's marks" that would be very easy to find on a Maltby receiver after 1941.
    A single letter over one or two numbers in a roundel.
    -----krinko

  7. #6
    FREE MEMBER
    NO Posting or PM's Allowed
    me2's Avatar
    Join Date
    Feb 2008
    Last On
    02-23-2012 @ 01:03 PM
    Posts
    175
    Local Date
    04-25-2025
    Local Time
    04:46 PM
    Thread Starter
    I'm not a good photographer but hoping you can see the general layout of these stamps. They are from top to bottom:

    Broad arrow
    crown
    N
    66
    It is straight forward stamping, no roundel. Also, this rifle has an A stamped above the last 2 digits in the serial number which should indicate there is something NOT standard about the rifle according to various sources. Could this fact be a possible reason for the N66 stamp?
    The metalwork is surprisingly smooth and it appears to be blued not Suncorited. All stamps are sharp and with no signs of having been restruck or polished. For a 1942 rifle this to me seems strange. Finish was the least concern during the pressure put on production during WWII. It has absolutely no import marks, not even the often seen "Englandicon" stamp. This one has been somewhat of a puzzle to me.

  8. #7
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    04-20-2025 @ 11:18 AM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,645
    Real Name
    Peter Laidler
    Local Date
    04-25-2025
    Local Time
    09:46 PM
    It's an examination mark and not a manufacturers mark. I believe the examiners used to travel between factories or be changed around, hence the old fashioned title 'travelling viewers'

  9. The Following 3 Members Say Thank You to Peter Laidler For This Useful Post:


+ Reply to Thread

Similar Threads

  1. Heat Lot Codes
    By gap in forum M1 Garand/M14/M1A Rifles
    Replies: 4
    Last Post: 01-28-2011, 11:21 PM
  2. OT - Carbine Part Supplier Out of Business?
    By Tired Retired in forum M1/M2 Carbine
    Replies: 7
    Last Post: 12-29-2010, 11:22 AM
  3. K98 Codes
    By lable in forum Mauser Rifles
    Replies: 3
    Last Post: 03-13-2010, 09:23 PM
  4. Was this sling manufacturer a USGI supplier?
    By RBruce in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 4
    Last Post: 08-05-2009, 12:27 PM
  5. Supplier of old parts
    By sdh1911 in forum Gunsmithing for Old Milsurps
    Replies: 0
    Last Post: 01-01-2007, 12:37 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts